untitled3

This is the 6 Channel Hitec Optic 6 FM/Q-PCM Radio Control System

with Spectra Module and HPD-07RH receiver.

Power Plane/Sailplane and Helicopter Mixing Capability

FEATURES: Spectra Module allows easy tuning to all 72MHz channels

Programmable shift allows usage with all PPM/FM receivers

Eight model memory with model naming capability

Assignable switches

Throttle lock and engine cut

Dual Timer

CCPM and CROW mixing

Throttle and pitch curves

Two open mixes

End Point Adjustment (EPA)

Dual Rates

Exponential

Fail Safe

Trainer jack, requires #58310 Trainer Cord, HRCM8310 (not included)

One year limited warranty

DX7 7Ch Air w/AR7000 & 4-DS821 MD2

Key Features

20-model memory

Airplane and Heli software

Switch assignment

P-mixes

Includes 4 powerful DS821 digital servos with high-tech resin gears

3-axis dual rate & expo

3-position flap (Airplane)

5-point throttle curve (Heli)

3 flight modes plus hold (Heli)

Gyro programming (Heli)

CCPM, 2-servo 90 degree, 3-servo 90 degree, & 3-servo 120 degree

Configured to default to airplane model type (all heli programming is available

Specs

# of Channels:7

Modulation:DSM2

Band:2.4 GHz

Servos:DS821 Sport Digital Servos

Receiver:AR7000

Programming Features:Aircraft and Heli

Model Memory:20 Model Memory

Transmitter (Tx) Battery Type:1500mAh Ni-MH

instock $ 349.99

Airtronics RDS8000 2.4GHz FHSS Radio TX & RX

The RDS8000 is a full-featured 8-channel system, packed with capabilities for all types of aircraft. A top-quality digital radio, the RDS8000 is noted for its ease-of-operation and programming. Helicopter, fixed wing aircraft and sailplane pilots will all benefit when using the standard features of the RDS8000.

Whether flying a basic model or one that requires advanced features, the RDS8000 can do it all! One of the key features of the RDS8000 is the ability to use both basic or advanced program menu.

The RDS8000 makes programming easier by allowing you to turn off any programming screen not required. Because it uses Airtronics' FHSS 2.4GHz communications technology you never have to worry about an 'open frequency'. Fly any time with confidence.

INSTOCK 155.00 W/ RX

Airtronics 8CH 2.4GHz FHSS Receiver (RDS8000)

This receiver utilizes Airtronics FHSS 2.4GHz technology. This means that no crystal is necessary.

This receiver uses the standard Z connector.

This receiver can be used with Airtronics RDS8000 2.4GHz Transmitters.

Dimensions: 47 x 27.5 x 15.2 mm

INSTOCK $ 80.00

HS-55 The HS-55 set the standard for affordable performance, offering precision components that have been engineered to provide long lasting trouble free service! Featured in a hundred model aircraft reviews worldwide, the HS-55 is your best choice when it comes to controlling” smaller” electric’s and Park Flyers.

Motor Type: Coreless

Bearing Type: None

Speed: 0.18 / 0.14 sec @ 60deg.

English Metric

Torque: 15.27 / 18.05 oz.in (4.8v/6v) 1.1 / 1.3 kg.cm

Size: 0.89" x 0.45" x 0.94" 22.80 x 11.60 x 24.00mm

Weight: 0.28oz 8.00g

HS-645MG

The powerful HS-645MG is one of Hitec’s most popular servos. It’s the perfect choice for those larger sport planes or monster trucks and buggies requiring a durable high torque servo. Featuring our unique M/P and metal gear train technology, the HS-645MG offers one of the strongest gear trains available in any servo.

Motor Type: 3 Pole

Bearing Type: Dual Ball Bearing

Speed: 0.24 / 0.20 sec @ 60 deg.

English Metric

Torque: 106.93 / 133.31 oz.in (4.8v/6v) 7.7 / 9.6 kg.cm

Size: 1.59" x 0.77" x 1.48" 40.60 x 19.80 x 37.30mm

Weight: 1.94oz 55.20g

Airtronics MX-3 3ch 2.4 GHz FHSS Radio Transmitter & Receiver

The new MX-3 FHSS (Frequency Hopping) 2.4 GHz Spread Spectrum radio system is based on the revolutionary MX-3.

Now you can have crystal FREE, interference FREE performance in the comfortable MX-3 chassis.

The MX-3 FHSS has all the features of the MX-3, plus 18 Model Memory. You can save all of your models and setups in one transmitter and be on your way to the track.

Never worry about having the correct crystal, because you have crystal FREE interference FREE 2.4 GHz technology.

The MX-3 FHSS is available as a transmitter and receiver system that includes: 2.4 MHz Transmitter, Receiver and Dry Battery Holder. Additional 2.4 GHz 92324 3 channel receivers are available separately.

MX-3 3ch FM Comp w/1 94102Z - 75 MHz

Features

FM Transmitter and Reciever

Never Change Crystals Again!

3 Channel FM Computer System

Digital Dual Rate Steering Adjustment

Digital Throttle Trim

Digital Steering Trim

Auxillary Channel 3 Lever

Adjustable (70/30) Throttle Trigger

Soft Touch Programming Keys

Eronomic Comfor Handle

Charging Jack for Optional Transmitter NiCd Battery Pack

Wrist Strap Support

4 Cell Dry Battery Holder

Switch Harness

Large LCD Display on Transmitter

Black & Chrome Steering Wheel

18 Model Memory

Unique and Functional Pistol Grip Transmitter Design

Well balanced for precise control

Non-slip rubber steering wheel

Well placed digital trim levers

Optimum third channel switch location

Adjustable Throttle trigger

Low Battery warning

Sound Beep On/Off

Airtronics 3ch Super Micro N/B Receiver 75MHz Synthesized

This receiver does not require a crystal! Simply dial in any of the 30 channels available for 75MHz operation.

Dimensions: 1.66 x 1.06 x 0.63 inches

Weight: 18.5 grams

Airtronics 3ch Super Micro Receiver 27MHz FM Synthesized

Click here to add text.

This receiver does not require a crystal! Simply dial in any of the 6 channels available for 27MHz operation

Dimensions: 1.66 x 1.06 x 0.63 inches

Weight: 18.5 grams

Aggressor CRX

Considered a top level competition grade FM surface radio system, while still keeping the sport user in mind, the Aggressor CRX has all the features of radios costing $100 more. With 3-channels, 20-model memories, a high definition graphic LCD display, digital trims, push button third channel shift, and easy to program user interface, the CRX is a favorite with racers and back yard bashers.

Features

3 Channel FM

Dual Rate steering

Steering wheel tension adjustment

Trim center audible verification

Transmitter Low Battery Alarm

Interchangeable assorted color rubber grip pads in two sizes

Model Naming. (6 Characters)

Sub-Trims

Ch #3 Switch Set. (Shift, Linear)

Steering and Throttle Exponential travel

Timer(Up/Down)

Servo Reversing

Model Reset. (Factory default)

2.4Ghz Compatible with aftermarked module

High definition/multi-pixel LCD Display

Brake ATL switch brake lever travel limiter

Third channel "Shifting" button

Third channel "Linear" digital trim

Digital Trims

RF Indicator light

Two-speed menu scrolling

Model select. (20 models)

EPA. (End Point adjustment)

ABS. (Anti-Lock braking)

Steering to Aux/Throttle to Aux Mixing

Model Copy

RF Indicator light

Total Transmitter "On" Time Timer

Eclipse 7

Considered one of the best aircraft control systems in the market today, the Eclipse 7 is loaded with features, 7-channels, 7-model memory, shift changeability so you can use any brand of FM 72Mhz. receiver, optional 50-channel SPECTRA synthesizer module to select any channel to fly on, and specific programming for helicopters, gliders, and glow, gas or electric fixed wing aircrafts. The Eclipse 7 has the quality, value, and features that you have come to expect from Hitec. For R/C Pilots that demand an extra level of performance and reliability, Hitec has created a “super fast response” PCM technology called “Quick Pulse Code Modulation” in the Eclipse 7. The “Quick” PCM signal has an incredible 0.011 second response rate for the solid control feel you want for your heli or gas powered airplane.

Features

3 in 1 System (Heli, Glider Fixed wing)

Digital Trims

Trainer Capable

Model Copy

In-flight Timer

Shift Selectable

Servo Reverse all Channels

EPA's all Channels

Three Conditional Mixes

Dual Rates Channels 1, 2 and 4

Throttle Cut Switch

Engine Hold

FM or QPCM Modulation

7 Model Memory

Sub Trims

7 Character Model Naming

Data Reset to Defaults

Low Battery Warning

Shift Selectable

Servo Reverse all Channels

Five Programmable Mixes (2 in Heli mode)

Exponential Rates on Channels 1, 2 and 4

Auto Engine Cut

RADIOACCESSORIES

BACK TO TOP OF PAGE

This is the Futaba GY401 Gyro with an S9254 Digital Servo.

This is a high performance, compact and lightweight

(AVCS) Angular Vector Control System gyro developed for model helicopters.

Because the sensor and control circuit are integrated, it is simple to install.

FEATURES: AVCS System: Since the rudder trim changes (caused by wind and other

meteorological changes) the front, rear, and other heli attitudes

change and are automatically cancelled; tail (rudder) operation is

easy, making it perfect for 3D flight.

(also known as heading hold gyro)

SMM Gyro Sensor: Use of this newly developed technology virtually

eliminates rudder trim changes during flight (see COMMENTS).

Digital Servo Compatible (DS Mode): DS mode makes it compatible with

Futaba Digital Servos. This maximizes the high-speed response

performance of the Digital Servo.

Included high-speed S9254 Digital Servo boasts 47 oz-in torque and a

speed of .06 sec/60°

Remote Gain Function and Mode Switching Function Remote: Gain

function allows sensitivity switching from the transmitter and mode

switching function allows AVCS/normal gyro mode switching.

Integrated, compact and lightweight design made possible by high

density mounting technology.

Conductive Resin Case: This case improves EMC (Electrostatic and

electromagnetic interference) resistance.

One year warranty

INCLUDES: One GY401 gyro

One S9254 Digital servo, available separately FUTM0224

One .81" (20.5mm) round servo horn, one 1.8" (45mm) round servo horn

one 1.25" (32mm) 6 point servo horn, one 1.5" (39mm) 4 point horn,

mounting hardware

One mini plastic adjustment screwdriver

Three mounting pads

One instruction sheet

SPECS: GY401 Gyro- S9254 Digital Servo

Length: 1.1" (27mm) 1.6" (40mm)

Width: 1.1" (27mm) .79" (20mm)

Height: .79" (20mm) 1.4" (36.2mm) not including horn

Weight: .95oz (27g) 1.8oz (50g)

Torque: 47 oz-in

Speed: .06 sec/60°

Futaba GY401 Gyro w/S9254 Digital Servo

MORE TO COME

Designed for sport electric cars and boats with NiCd or NiMH batteries.

Great for 750mAh “AAA” cells, nitro receiver packs and the highest capacity sub-C size cells.

With 1.5A, 3A and 5A charge settings.

Built-in jack for charging 4-5 cell nitro receiver packs.

Five ramping LEDs show charge status

CHARGERS

Onyx 200 AC/DC Sport Peak Charger w/LEDs

$42.99 INSTOCK

Onyx 220 AC/DC Programmable Peak Charger w/LCD. $61.99 INSTOCK

FEATURES: Charges 4-8 cell NiCd or NiMH 4.8 - 9.6V cells with a capacity range

of 50 - 9900mAh

Pushbutton controls and audible tones for easy setup and control

Five battery memories are included for quick changes between battery

types

Fully adjustable charge currents and NiCd and NiMH flexibility for a

wide range of applications

Precise peak detection with automatic TRICKLE charge fills packs

completely for optimum voltage and run time, 3 - 20mV adjustable

peak detection helps to customize charger-to-battery performance

Built-in jack included for charging 4 or 5 cell NiCd or NiMH

receiver batteries for nitro models, even 8-cell transmitter

packs

Custom reversed LCD with backlight for easy viewing in any condition

shows input and output voltges, peak voltage, charge current,

charge capacity and time and more

Small, lightweight switching AC power supply delivers up to 5 amps

of charge current

Solid state reverse polarity and current overload safety devices

FIVE YEAR warranty

DuraTrax Onyx 210 AC/DC Peak Charger w/LCD $ 52.99 INSTOCK

FEATURES: Charges 4-8 cell NiCd or NiMH (4.8 - 9.6V) cells with a capacity

range of 750-7500mAh

NiCd and NiMH compatibility with custom peak detection

Pushbutton controls, audible tones and a custom LED with backlight

for easy setup and use

Selectable charge currents of 800mA, 1.5A, 3A and 5A

Automatic TRICKLE charge fills pack completely after peak charge for

optimum battery performance

Precise peak detection algorithm with automatic TRICKLE charge fills

packs completely for optimum voltage and run time

Built-in jack included for charging 4 or 5 cell NiCd or NiMH

receiver batteries for nitro models and even transmitter batteries

LCD shows battery voltage, charge current, time, capacity, battery

type and more

Small, lightweight switching AC power supply delivers up to 5 amps

of charge current

Solid state reverse polarity and current overload safety devices

FIVE YEAR warranty

Great Planes Electrifly Triton2 DC Computer Charger

FEATURES: Great for many applications including Airplane and Heli Batteries,

Tx and Rx batteries, Field Batteries and more

Handles 1-24 cell NiCd/MH (1.2 - 28V)

1-5 cell Li-Ion or LiPo (3.6 or 3.7V cells)

6, 12, 24V Pb cell (2V per cell)

Precision Zero DeltaV Peak Detection with adjustable sensitivity

for NiCd and NiMH batteries

"Constant Current / Constant Voltage" charge method for Pb and

Li-Ion/LiPo batteries

Fast Charge Thermal Cutoff (GPMM3151 Thermal Probe available

separately)

Top-Off Charge feature fully charges NiMHs without overheating

0-250mA adjustable TRICKLE Charge current (NiCd and NiMH only)

.1-3A Adjustable Discharge Current

Adjustable Discharge Cutoff Voltages for NiCd/MH, pre-set voltages

for Pb and LiPo/Ion

Perform 1 to 10 cycles (NiCd/MH only)

Recall data for 10 full cycles

Configure up to 10 batteries in memory for instant, easy recall and

charger setup

Displays Input and Output Volts, Peak Volts, Avg Dsch Volts, Chg and

Dsch Capacity, Currents and Time, Error Messages (No Battery

Connected, Open Circuit, and Reverse Polarity)

Audible sound cues aid in programming and notification of function

changes

Warning messages for Improper Input Voltage, Poor Connections,

Unsuitable Battery Condition, Reverse Polarity on output

Safety features include Cool-Off Time Delay, Maximum NiMH Charge

Input, Fast Charge Safety Timer, Current Overload and Reverse

Polarity Protection

Built-in cooling fan for better charge efficiency and extended

charger life

Small and lightweight, with a super-sturdy aluminum case for rugged

durability

Full 1 year warranty

$ 104.99 IN STOCK

Venom Pro Charger w/ Power Supply - US

If you have been searching for just one RC battery charger to handle all of your charging needs, look no further than the Venom Multi Function Pro Charger. This charger is available in both DC and AC/DC power configurations so there are no limitations. This machine can handle charging, discharging, balancing (LiPO/LiON/LiFE cells), cycling and more.

If you have multiple kinds of RC vehicles and other battery charging needs, the Pro Charger is able to service multiple types of batteries. Many RC enthusiasts have to use a special LiPO charger, a separate RC charger for each type of battery and manage all of the plugs and cords. The Venom Multi Function Pro Charger handles five different kinds of batteries in just one machine; NiCD, NiMH, LiPO, LiON/LiFE and Lead Acid batteries.

LiPO and LiON and LIFE batteries can have multiple cells depending on the size of the battery and need special handling to fully charge them. The Venom Pro Charger can handle 1 to 6 cell LiPO, LiON/LiFE at a time and a whopping one to fifteen cells for NiCD and NiMH batteries.

This system allows users to define charge rates from 0.1 amps to 5.0 amps depending on what they need. The Venom Multi Function Pro Charger also allows the user to create up to ten different charger profiles with a USB PC connection. If you use more than one RC car battery charger you can integrate all your power needs into one keeping track of each profile separately. To handle all the different kinds of vehicles there are six different power plugs; the new Traxxas® High Current Connector (TRX Plug)s, Tamiya, Alligator Clip, Futaba, Glow Igniter and JST plug.

The Chargers easy to use features include; Charging, Discharging, Cycling, Balancing (LiPO/LiION/LiFE cells), User definable charge rates from 0.1 amps to 5.0 amps, USB PC Linkability, Temperature Probe and 10 User-Defined Charger Profiles. Comes with six different charging plugs including the new Traxxas High Current Connector. Finally, an R/C battery charger that is as dedicated to performance as you are.

$ 139.99 INSTOCK

Intelligent Multifunction Charger Combo RCC-6SX+RCE-6BA $159.99 INSTOCK

RCC-6SX Intelligent multifunctional Charger/Discharger:

1. Apply to Ni-Cd, Ni-MH, Li-Ion, and Li-Poly batteries.

2.Special aluminum alloy anodic treatment outer case for good heat dissipation and great quality.

3.Use heat sink for the heat dissipation and extend the use life.

4. Automatic Ni-Cd/Ni-MH battery discharge/ charge cycle for battery activation.

5. Use RCE-6BA Li-Po Balancer to protect the batteries during charging, and extend the battery life, to improve the performance of battery and increase the power.

RCE-6BA Li-Po Balancer:

1.Separate balancing and charging ports eliminating charging amperage limit due to balancing wires’ gauge.

2.Dual mode balancer: Can be used as stand alone balancer, or concurrently with a separate charger.

3. Automatically balance 2~6 cells li-poly packs.

4.Balancing voltage resolution accurate to ±0.005V.

5.Individual cells’ balancing status displayed through LEDs.

6.Overcharging prevention circuitry with cutoff set at 4.26V/cell for additional safety, minimizing potential damages to the cells.

7.Low voltage cutoff set at 3.3V/cell to prevent over discharging of cells.

NOTE:

Do not leave the charger is operating unattended as it may cause a fire.

RCC-6SX Intelligent multifunctional Charger/Discharger:

●Input voltage:DC11~15V

●Charge output rate:Max 5A/125W

●Discharge rate:Max 1A/5W

●Li-Ion/Polymer:1~6cell(Auto Voltage Detection/Manual)

●Ni-MH:1~18cells

●Charge current:0.1A~5.0A(0.1A Step)

●Discharge current:0.1A~1.0A(0.1A Step)

●Discharge->Charge:1~5 cycles

●Charge->Discharge:1~5 cycles

●Safety timer:on/off, 1-900mins

●Key beep/Buzzer alarms: on/off

●12V Pb battery low voltage cut off: 11-15V(0.1V Step)

●Display:LCD 16char. x2 line(Backlight)

●Li-Ion/Polymer voltage type: Li-lon3.6V/Li-Poly3.7V

●Size:150x142x33mm

●Weight:580g

RCE-6BA Li-Po Balancer:

●Lithium polymer cell count: 2~6 cells in series configuration

●Balancing activation voltage:

Automatic:>0.03V imbalance

Manual: >0.01V imbalance

●Discharge current during balancing: 350mA

●Imbalance control voltage: +/-0.005V

●Maximum cell voltage cut off: 4.26V

●Low voltage cut off: 3.3V

●Balancing voltage resolution: +/-0.005V

●Size:83x45x19mm

●Weight:120g

Hobbico Quick Field DC Charger MkII 12 Volt

FEATURES: Super Easy to use, and comes with many safety features.

Simple push button start-up.

Peak Detection Charging for NiCd or NiMH packs.

Visual and audible error messages to indicate reverse polarity and

poor output connections.

Time-out Charge Termination and fused current overload protection.

Can be mounted on a Field Box, or used as a stand-alone unit.

Charges 1 to 3 cell Li-Ion or LiPo (Lithium Polymer) Park Flyer

batteries using "Constant Current/Constant Voltage" method

Charges 1-8 cell NiCd or NiMH radio batteries.

INSTOCK $ 54.99

MRC Super Brain 989 8-Cell Lithium Polymer Charger

FEATURES: 100-19,900mAh cell range

Charges single cell glow igniters, receiver and transmitter packs,

field batteries and much more

Constant Current/Constant Voltage up to 1.5C max for charging lithium

cells

Charge rate of up to 0.1A - 10.0A for NiCd/NiMH, and 1.2C max for

Lithium cells

Discharge rate of 0.1A - 10.0A with adjustable cut-off range

Adjustable automatic re-peak and top-off charge for extra boost

Adjustable peak sensitivity

Adjustable Temperature Cutoff Range from 100°-160°F (charge)

Motor break-in feature with adjustable time and output

1-30VDC 10A (120VA) adjustable output for comm lathe, tire cutter and

Temperature controlled fan prevents overheating

Built-in safety confirmation

inSTOCK $159.99

SPECS: R168DF Receiver;

Dimensions: 1.1 x 2.2 x 0.8" (28.5 x 55.5 x 19.8mm)

Weight: 1.0oz (28g)

S3004 Servo;

Speed: 0.23 sec/60° @ 4.8V

0.19 sec/60° @ 6.0V

Torque: 44 oz-in (3.2 kg-cm) at 4.8V

57 oz-in (4.1 kg-cm) at 6.0V

Length: 1.6" (41mm)

Width: 0.8" (20mm)

Height: 1.4" (36mm)

Weight: 1.3 ounce (37.2 grams)

Connector: "J" type with approx. 5" wire

NR4QB 600mAh Battery;

Length: 2.00"

Width: 1.12"

Height: 1.12"

Weight: 3.3 ounce

Volts: 4.8V

Charging: 60mA for 15 hours

Quick Charging: 180mA for 5 hours

Futaba 8-Channel Flight Pack R168DF/4 S3004s/NiCd

INSTOCK $124.99

Futaba 8-Channel Flight Pack R168DF/4 S3004 Servos INSTOCK $ 109.99

INCLUDES: One Flight Pack containing:

One R168DF FM Dual Conversion Receiver (FUTL0832)

Four S3004 Ball Bearing Servos (FUTM0004)

One Switch Harness with charging plug (FUTM4370)

One 9" Servo Extension Wire (FUTM3910)

One Set of Servo Accessories for all servos (FUTM3553 x 4)

Futaba Micro Flight Pack/R114F Rx/2 S3114 Servos High

INSTOCK $74.99

FEATURES: Range of approximately 600 feet (183m), perfect for park flyers

Designed for modelers who want to use a single radio transmitter

to fly several different model aircraft, especially pilots who

are utilizing computerized radios with multi-model memory

Single Conversion FM 72MHz High-band tuned receiver

One year warranty on the receiver and servos

INCLUDES: One High-Band Flight Pack containing:

R114F FM Single Conversion Receiver (FUTL0443)

Two S3114 Micro Servos (FUTM0414)

Two pre-installed .91" x .64" (23mmx16mm) 4 arm servo horns

Warranty Card

Switch Harness (FUTM4505)

DX5e 5Ch Full Range Transmitter/Receiver only MD2 by Spektrum.

Key Features

Basic 5-channel 2.4GHz DSM2 radio and receiver

Easy to use control for basic models

Includes AR500 5-channel full-range sport receiver

Delta wing mixing

HI/LO rates

Servo reversing

JR and Spektrum compatible trainer system

Overview

Spektrum introduces another enormous change for the RC industry—The most affordable full-range 2.4GHz radio ever available. The DX5e brings together the unbeatable control of genuine DSM2 technology with the simplest, easiest-to-use design available, letting anyone, from parkfliers to students to instructors and more, take advantage of Spektrum technology for less. For a Spektrum radio and an AR500 receiver, the DX5e is the greatest value in RC, putting 2.4GHz DSM control in your hands for less than ever before.

Specs

# of Channels:5

Modulation:DSM2

Band:2.4GHz

Servos:N/A

Receiver:AR500 5CH Full Range Sport Receiver

Programming Features:Servo Reverse; Delta Wing; HI/LO rates

Model Memory:1

Modes:Mode 1 and Mode 2 available

Transmitter (Tx) Battery Type:AA Heavy-duty (not included), Alkaline(included) or Rechargeable (not included)

Experience Level:Beginner

INSTOCK $ 99.99

Flight Leader Aluminum Case - Large $59.99

Flight Leader Aluminum Tote Case High quality, super-strong aluminum tote box with heavy duty construction and large enough to carry one or two transmitters and all of your field equipment. Features:

Two tough hinges

Two lockable over-center catches

Handle and removable carrying strap

Factory-cut foam liner

Strong, ribbed aluminum contruction

Versatile internal dividers for separate storage compartments

Neat storage pockets in the lid for small tools

This is the VoltWatch2 on-board Receiver Battery Monitor for

4.8V and 6V NiCd and NiMH receiver packs.

This mounts on the outside of the airplane, so you can see at a glance

the status of the receiver battery mounted inside.

FEATURES: 7-LEDs provide instant, accurate battery voltage status of Low, Safe,

or Max. Only one LED glows at a time

Small switch to select 4.8V or 6V battery

Very lightweight, only .15oz (4.3g) unit can mount on the side

of the fuselage, or under the plane's canopy

Draws amazingly low current - from 4-34mA depending on the battery

voltage

Plugs into any open receiver channel using a Futaba J connector

One year warranty

Hobbico VoltWatch2 4.8V/6V Rx Battery Monitor $12.49

Hobbico Air Alert Flight Pack Monitor

$15.99

This is an Air Alert Flight Pack Monitor used as a Low Voltage

and Lost Aircraft Alarm on Radio Controlled Aircraft.

FEATURES: Emits different sequences of "beeps" to signal potentially risky

flight pack conditions.

1. Low Battery Alarm- when flight pack voltage levels are low,

to identify an impending power failure.

2. Lost Airplane Finder- as a tracking device, when searching for

a model that has crashed.

3. Transmitter Inactivity Signal- if the respective Tx stick hasn't

been moved for over one minute, warns that either the

transmitter is not turned ON, or the receiver has not been

turned OFF, or some other signal problem exists.

For 4.8V battery pack ONLY

Easy flush mounting inside or outside the fuselage

Ultra lightweight, micro-thin case is foam-cushioned for durability

and to protect components inside.

Includes a Universal connector for use with most common radio systems

such as Futaba J, Airtronics Z, Hitec S, JR, Tower Hobbies.

2-year warranty

INCLUDES: One Air Alert Flight Pack Monitor w/One Male and One Female

Universal Connector

One 13/16" square of double-sided tape

One instruction card

REQUIRES: Plug Air Alert into receiver throttle channel, and throttle servo

into Air Alert. Turn receiver ON. Air Alert will emit One Beep

to confirm Power is ON.

Great Planes ElectriFly Triton EQ AC/DC Charger

INSTOCK 129.99

This is the ElectriFly AC/DC TritonEQ

Charger, Discharger and Cycler with Built-In Equalizer.

***Upgraded features over the ElectriFly Triton Jr. include;***

Lightweight built-in switching AC power supply, plus DC input capabilities

New reversed character LCD with backlight and 0-45° adjustable view angle

Built-in balancing for 1-6S LiPo, Li-Ion or LiFe (A123) cells

with FlightPower and ElectriFly adapters

FEATURES: Charges 1-14 cell NiMH and NiCd cells and 1-6 cell LiPo, Li-Ion and

LiFe (3.6, 3.7 or 3.3V cells)

Peak detection technology for NiCd and NiMH batteries, and constant

current/constant voltage technology for lithiums and lead-acid

batteries

Ideal for radio batteries and with charge currents adjustable from

100mA to 5 amps (limited to 1C for lithiums) it can also handle

large power packs

Built-in balancing for up to 6S packs makes it ideal for the smallest

indoor fliers up to big outdoor powerhouses with no need for

external balancer

Discharge cutoff voltage can be adjusted for NiCd/MH, and is fixed

for lithiums and lead-acid batteries

NiCd and NiMH trickle current is automatically set at 1/20th of

the fast charge current setting

Reversed LCD with backlight plus a 0-45° adjustable view angle

clearly displays input and output volts, peak volts, individual

lithium cell voltages, average discharge volts, charge and

discharge capacity, currents and time, error messages and more

Touchpad controls and super-simple programming make for

simplicity and reliability

Safety features include fast charge safety timer, current overload

and reverse polarity protection

One year limited warranty

INCLUDES: ElectriFly AC/DC TritonEQ with with FlightPower and ElectriFly

adapters, AC power cord, DC power cord with alligator clips and

instruction manual

SPECS: AC Input Voltage: 110V 60Hz - 240V 50Hz (detachable AC cord)

DC Input: 11-15.0V DC, with large alligator clips

Number of Outputs: One, banana jacks

Battery Types, # cells: 1-14 NiCd, NiMH

1-6 LiPo, Li-Ion, or LiFe (3.6, 3.7 or 3.3V cells)

2, 4, 6, 8, 10, 12V Pb (2V per cell)

Fast Charge Current: 0.1-5.0A (1C maximum for lithiums)

63W max DC, 50W max AC

Fast Charge Termination: Peak detection NiCd, NiMH, cc/cv for Pb and

lithiums

Trickle Current (NiCd/MH only): Chg current / 20

Peak Sensitivity (NiCd/MH only): 8mV NiCd, 5mV NiMH

Peak Delay at Start (NiCd/MH only): 3 minutes

Fast Charge Safety Timer: NiCd/MH 1.5 hours, lithiums 3 hours, or

turn off

Lithium Balancing Accuracy: 5mV per cell

Lithium Balancing Connector: FlightPower and ElectriFly adapters

included

Lithium Max. Node Current: 300mA

Discharge Current: 0.1-1.0A (5W max)

Discharge Cutoff Voltage: NiCd, NiMH 0.1-16.8V

LiPo, Li-Ion 3.0V per cell

LiFe 2.5V per cell

Pb 1.8V per cell

Cycle Count (NiCd, NiMH only): 1-5 cycles

Battery Memories: One

Programming Controls: Membrane touchpad, 4 buttons

Display Type: 2x16 reversed LCD w/backlight and adjustable angle

Audible Indicators: Beeper

Case Material: Aluminum and ABS plastic

Safety Devices: Solid-state reverse polarity and overload

Case Size: 5.9 x 6.0 x 2.3 in (150 x 153 x 58mm)

Weight: 23.8oz (675g, w/o AC power cord)

DuraTrax Onyx 100 AC/DC Peak Charger NiCd NiMH

instock $31.99

FEATURES: Ideal for sport electric car or boat modelers needing a charger that

operates on either AC or DC input power and automatically peaks

both NiCd and NiMH batteries as small as 600mAh "AAA" and as big as

sub-C size-good for 1/18-1/8 scale models

Lightweight switching AC power supply is great for portability and

small pit areas

Selectable charge currents of 1A, 2A (2A limit on AC) or 4A linear

Peak detection intelligence eliminates need to track charge state of

battery before charge

Automatic trickle charge tops off packs to maximum power

Auto-start function with status LED makes setup and use a snap

Built-in socket for connecting radio batteries

DC power lead with alligator clips connects to many 12V DC power

sources

Five year warranty

SPECS: AC Input: 110V AC 60Hz

DC Input: 11-15V DC, built-in lead with alligator clips

Battery Types: 4-8 NiCd or NiMH Cells (4.8-9.6V, limited to 7 cells

on DC)

Battery Capacity Range: 600-6000mAh

Fast Charge Current: 1, 2, or 4A linear (2A limit on AC)

Fast Charge Termination: Peak detection

Fast Charge Safety Timer: 90 minutes

Peak Sensitivity: 8mV

Auto-Trickle Current: 1/20 fast charge setting

Controls: auto-start, switchable current selector

LED Indicator: Red

Output Connections: Built-in lead with standard connector

Built-in jack for radio batteries

Protective Devices: Solid-state reverse polarity and current overload

Case size: 4.1 x 3.5 x 1.1" (104 x 90 x 29mm)

Weight: 9.17 oz.(260g)

THE SQUID CHARGING CORD

RACES EDGE 14.99 INSTOCK

ProPeak Gallant EQ Balance Charger/Cycler LiPo/Fe/NiMH/pB $79.99

DC Balancing Charger for Li-Po, Li-Fe, Ni-MH, Ni-Cd, and Lead-Acid Batteries

Balance Charges 1-6 cells

Cycles

Charges

Discharges

high performance, micro-processor controlled, fast charger/discharger has a built-in Lithium balancer. It's perfect for charging Li-Ion, Li-Po, Li-Fe, Ni-MH, Ni-Cd and Lead Acid batteries from a 10~18.0v DC power source. Maximum internal circuit power = 50W. Variable charge current = up to 5.0A. Charging and discharging cycles, 5 regime memories, a storage setting for Lithium packs and much more.

Hitec Spectra 2.4GHz Module & 2-Optima 7Ch 2.4GHz Rx $129.99

Airtronics MX-Sport 2.4G FHSS-2 Computer Radio (TX/RX)

Venom Pro Charger Plus w/Power Supply US $199.99

Venom’s new Multi Function Pro Charger Plus is available in an AC/DC power configuration to suit a variety of user needs. The Venom Pro Charger Plus will charge 1 to 8 cell LiPO and LiION/LiFE Battery Packs, as well as NiCD and NiMH battery packs with 1 to 27 cells and Lead Acid Batteries. The Venom Pro Charger Plus has many easy to use features which include; Charging, Discharging, Cycling, Balancing (LiPO/LiION/LiFE cells), User definable charge rates from 0.1 amps to 7.0 amps, USB PC Linkability, Temperature Probe and 10 User-Defined Charger Profiles. Comes with six different charging plugs including the Traxxas® High Current Connector (TRX Plug). The Venom Pro Charger Plus is a perfect compliment to Venom’s extensive line of batteries using the Traxxas® High Current Connector.

Specifications

AC/DC compatible with included AC power adapter

Input: 12V DC

Length: 164mm

Width: 120mm

Height: 45mm

Weight: 21.1oz/598g

Charging Capabilities

LiPO/LiION/LiFE: 1-8 cells

NiMH/NiCD: 1-27 cells

Lead Acid (Pb): 2V-36V

Charge Rate: 0.1 – 7A

Discharge Rate: 0.1A – 5A

Charge / Discharge Cycles: 1 to 5 cycles

10 Profile memory

USB PC link

Hitec Aurora 9 2.4GHz Tx & Optima 7-Channel Rx

FEATURES: AFHSS (Adaptive Frequency Hopping Spread Spectrum) 2.4GHz/PPM/PCM

compatible

Ideal for airplanes, sailpanes and helis

Standard programming features include 9 Assignable Control Channels,

3 Model Types (ACRO/GLID/HELI) Programming, 30 Model Memories,

Servo Reverse Speed and Monitor, 8 Flight Conditions with 10

Characters and more

Advanced ACRO programming includes, 9 Wing Type (6 Main Wings, 3

Flying Wings), 5 Tail Type, Quick Model Options Select, 7 Point

Throttle Curve, 3X Gyro Sensitivity, Snap Roll and more

Advanced GLIDER programming includes Motor Control, Airbrake,

9 Wing Type, 5 Tail Type, Butterfly, V-Tail, Delta Mix, Launch,

Camber Mix, Ailevator, Flap Control, Aileron Diff and more

Advanced HELI programming includes 6 Swash Types, 7 Point Throttle

and Pitch Curves, Quick Model Options Select, Swash and Rudder to

Throttle Mix, Gyro Sensitivity, Fuel Mixture, Throttle Hold and

One year limited warranty through manufacturer beginning at date of

purchase

INCLUDES: Transmitter with 2.4GHz Spectra Module

Optima 7 7-Channel Receiver, HRCL7000

#54128 6-cell 1300mAh Transmitter Battery

CG-S45 AC Wall Charger

On/Off Switch, Y-Harness, Receiver Foam and Instruction Manual

REQUIRES: Programming, charging transmitter and receiver batteries

Servos and receiver battery of modeler's choice

SPECS: Aurora 9 Transmitter;

Modulation: 2.4GHz/PPM/QPCM

Power Supply: 7.2V NiMH Battery

Current Drain: 300mA

Optima 7 Receiver:

Size: 2.24 x 0.82 x 0.44" (57 x 21 x 11.4mm)

Weight: 0.60oz (17g)